Juniper JN0-280 Dumps

B.   Exchange

Answer DescriptionExplanation:

In OSPF, routers exchange link-state information in different stages to establish full adjacency. TheMTU sizeis checked during theExchangestate.

Step-by-Step Breakdown:

OSPF Adjacency Process:

OSPF routers go through multiple stages when forming an adjacency:Down,Init,2-Way,ExStart,Exchange,Loading, andFull.

Exchange State:

During theExchangestate, OSPF routers exchangeDatabase Description (DBD)packets to describe their link-state databases. TheMTU sizeis checked at this stage to ensure both routers can successfully exchange these packets without fragmentation.

If there is anMTU mismatch, the routers may fail to proceed past the Exchange state.

Juniper Reference:

MTU Checking in OSPF: Junos uses the Exchange state to check for MTU mismatches, ensuring that routers can properly exchange database information without packet fragmentation issues.

D.   [edit chassis]

Answer DescriptionExplanation:

To configureaggregated Ethernet (AE) interfaceson a Junos device, the configuration is done under the[edit chassis]hierarchy.

Step-by-Step Breakdown:

Chassis Configuration:Thechassisconfiguration is responsible for enabling the hardware to supportLink Aggregation Groups (LAGs), allowing multiple physical interfaces to be bundled into a single logical interface for load balancing and redundancy.

Command Example:

set chassis aggregated-devices ethernet device-count

This command enables a specific number of aggregated Ethernet interfaces on the device.

Juniper Reference:

LAG Configuration in Junos: Thechassishierarchy is used to allocate and manage hardware resources for aggregated Ethernet interfaces in Juniper devices.

B.   BGP provides the control plane within the overlay network.


C.   OSPF provides the control plane within the overlay network.

Answer DescriptionExplanation:

EVPN-VXLANis an overlay technology used in data center networks to extend Layer 2 services over a Layer 3 network.

Step-by-Step Breakdown:

BGP Control Plane:BGP (Border Gateway Protocol)is used as the control plane for EVPN-VXLAN. BGP advertises MAC addresses and IP address reachability information across the VXLAN network, enabling efficient multi-tenant Layer 2 connectivity over a Layer 3 infrastructure.

Encapsulation:VXLAN (Virtual Extensible LAN)encapsulates Layer 2 frames into Layer 3 packets. This encapsulation allows Layer 2 traffic to be transported across a Layer 3 network, effectively creating a tunnel for Ethernet frames.

Juniper Reference:

EVPN-VXLAN Configuration: Juniper supports EVPN-VXLAN with BGP as the control plane, allowing scalable Layer 2 connectivity over a routed infrastructure in modern data centers.

B.   Reject all routes.

Answer DescriptionExplanation:

In Junos, thedefault export policyforOSPFis toreject all routesfrom being exported.

Step-by-Step Breakdown:

Default Export Policy:By default,OSPFin Junos does not export any routes to other routing protocols or neighbors. This is a safety mechanism to prevent unintended route advertisements.

Custom Export Policies:

If you need to export routes, you must create a customexport policythat explicitly defines which routes to advertise.

Example: You can create an export policy to redistribute static or connected routes into OSPF.

Juniper Reference:

OSPF Export Behavior: In Juniper devices, the default policy for OSPF is to reject route advertisements unless explicitly configured otherwise through custom policies.

A.   a Layer 3 routing protocol


B.   a single connection between each spine and leaf

Answer DescriptionExplanation:

AnIP fabricis a network architecture commonly used in data centers to provide scalable, high-throughput connectivity using aspine-leaf topology.

Step-by-Step Breakdown:

Layer 3 Routing Protocol:An IP fabric relies on aLayer 3 routing protocol, typically BGP or OSPF, to provide routing between the leaf and spine switches. This ensures efficient traffic forwarding across the network.

Single Connection Between Spine and Leaf:In an IP fabric, each leaf switch connects toevery spine switchwith a single connection. This ensures that traffic between any two leaf switches can travel through the spine layer in just two hops.

Juniper Reference:

Spine-Leaf Design: Juniper’s IP fabric implementations are designed for scalability and low-latency routing, often using protocols like BGP for Layer 3 control.

A.   EBGP peers have a TTL of 1, while IBGP peers have a TTL of 255.


C.   EBGP routes are more preferred than IBGP routes.

Answer DescriptionExplanation:

EBGP (External BGP)andIBGP (Internal BGP)operate with different rules due to the nature of their relationships.

Step-by-Step Breakdown:

TTL Differences:

EBGP: By default, EBGP peers have a TTL of 1, meaning they must be directly connected, or the TTL needs to be manually increased for multihop EBGP.

IBGP: IBGP peers within the same AS have a TTL of 255, as they are expected to communicate over multiple hops within the AS.

Preference for EBGP Routes:

Routes learned viaEBGPare typically preferred over IBGP routes. This is because EBGP routes are considered more reliable since they originate outside the AS, while IBGP routes are internal.

Juniper Reference:

BGP Configuration: The different handling of TTL and route preferences between EBGP and IBGP ensures proper route selection and security within Junos-based networks.

D.   BGP

Answer DescriptionExplanation:

EVPN (Ethernet Virtual Private Network)is a standard protocol used for building Layer 2 and Layer 3 VPNs over an IP or MPLS network. Thesignaling protocolused for EVPN isBGP(Border Gateway Protocol).

Step-by-Step Breakdown:

BGP as the EVPN Signaling Protocol:EVPN uses BGP to exchange MAC address reachability information between routers (PE devices). This enables devices to learn which MAC addresses are reachable through which PE devices, facilitating Layer 2 forwarding across an IP or MPLS core.

BGP Extensions for EVPN:BGP is extended with new address families (e.g., EVPN NLRI) to carry both MAC and IP address information, allowing for scalable and efficient multi-tenant network solutions.

Juniper Reference:

Junos EVPN Configuration: Juniper uses BGP as the control plane for EVPN to exchange MAC and IP route information between different data center devices.

C.   By default, IBGP has a TTL of 255.


D.   IBGP uses full mesh for loop prevention.

Answer DescriptionExplanation:

IBGP (Internal Border Gateway Protocol)is used to exchange routing information betweenrouters within the same AS (Autonomous System).

Step-by-Step Breakdown:

TTL of 255:

By default, IBGP sessions are established with aTTL (Time to Live)value of255. This allows IBGP neighbors to communicate over multiple hops within the AS without requiring any additional configuration.

Full Mesh Requirement:

IBGP requires alogical full meshbetween all IBGP routers to ensure that routing information is fully distributed within the AS. Since IBGP does not propagate routes learned from one IBGP peer to another by default, a full mesh topology is needed unlessroute reflectorsorBGP confederationsare used.

Juniper Reference:

IBGP Full Mesh: Juniper recommends using route reflectors in large networks to simplify IBGP full-mesh requirements.

C.   The chance of packet collision is increased.


D.   The amount of network resource consumption is increased.

Answer DescriptionExplanation:

Acollision domainis a network segment where data packets can "collide" with one another when being sent on the same network medium.

Step-by-Step Breakdown:

Increased Collision Probability:If all devices are in asingle collision domain, the likelihood of packet collisions increases as more devices attempt to send packets simultaneously, leading to network inefficiencies.

Increased Resource Consumption:More collisions result inincreased network resource consumptionas devices need to retransmit packets, causing higher utilization of bandwidth and slowing down network performance.

Juniper Reference:

Collision Domains: Proper network segmentation using switches reduces collision domains, thereby improving network performance and reducing packet collisions.

B.   You can configure BFD per interface within the protocol stanza.


C.   The BFD operation always consists of minimum intervals and multipliers.

Answer DescriptionExplanation:

Bidirectional Forwarding Detection (BFD)is a protocol used to detect faults in the forwarding path between two routers. It provides rapid failure detection, enhancing the performance of routing protocols like OSPF, BGP, and IS-IS.

Step-by-Step Breakdown:

Per Interface Configuration:BFD can be configured on aper-interfacebasis within the protocol stanza (e.g., OSPF, BGP). This allows granular control over where BFD is enabled and the failure detection intervals for specific interfaces.

Minimum Interval and Multiplier:BFD uses aminimum interval(the time between BFD control packets) and amultiplier(the number of missed packets before the path is declared down). The combination of these two defines the detection time for failures.

Juniper Reference:

BFD Configuration: In Juniper, BFD is configurable within routing protocol stanzas, with the failure detection mechanism always based on minimum intervals and multipliers.