Question # 1
| A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which strategy will reduce the negative impact of the design? |
| A. Resurvey and adjust the design. | | B. Deploy unsurveyed access points to the design. | | C. Deploy the specified access points per area type. | | D. Increase the Tx power on incorrectly surveyed access points. |
A. Resurvey and adjust the design.
Explanation:
The most effective way to address the issue is to resurvey the areas with the correct survey devices. This ensures that the design accurately reflects the performance characteristics of the specified access points for each area type, leading to a more reliable and efficient wireless network design tailored to each environment’s specific needs.
Question # 2
An enterprise is using the wireless network as the main network connection for corporate users and guests. To wireless network availability. Two Standalone controllers are installed in the head office. APs are connected to the controllers using a round-robin approach to load balance the traffic. After a power cut, the wireless clients disconnect while roaming. An engineer tried eping from the controller but faits. Which protocol needs to be allowed between the networks that the controllers are installed?
|
| A. IP Protocol 67 | | B. IP Protocol 77 | | C. IP Protocol 87 | | D. IP Protocol 97 |
D. IP Protocol 97
Explanation:
The protocol that needs to be allowed between the networks where the controllers are installed is IP Protocol 97, which is used for encapsulating IP within IP, often used in network mobility and IP tunneling.
Question # 3
| An engineer is trying to configure the APs installed in a new auditorium to use 40 MHz channels with high data rates and lower TX power. The APs in the building hallway must use lower-density design settings configured for the rest of the building. Which two configurations achieve this design? (Choose two.) |
| A. TPC | | B. DCA | | C. RRM | | D. RF protocol |
C. RRM
D. RF protocol
Explanation:
AP groups allow the engineer to apply different policies for APs in the auditorium versus those in the hallway. RRM (Radio Resource Management) can dynamically adjust the TX power and channel settings to optimize the wireless coverage and capacity.
Question # 4
| An engineer must assess an existing company WLAN to determine the possibility for future IEEE 802.11ac Wave 2 wireless deployment. The existing WLAN is IEEE 802.11a/n and has IEEE 802.11n and 802. 11a clients. The engineer must advise the customer about support for these older clients on the new APs. What happens with client compatibility? |
| A. 802.11ac is backward compatible with 802.11n but not with 802.11a. | | B. 802.11ac is backward compatible with 802.11a but not with 802.11n. | | C. 802.11ac is backward compatible with 802.11a and 802.11n. | | D. 802.11ac is not backward compatible with 802.11a or 802.11n. |
C. 802.11ac is backward compatible with 802.11a and 802.11n.
Explanation:
IEEE 802.11ac Wave 2 APs are backward compatible with 802.11a/n clients, allowing these devices to connect and communicate with the newer APs, albeit at their respective maximum supported speeds.
Question # 5
| An engineer is designing a network deployment for a technology company. The company has four buildings with access points that must provide seamless wireless coverage and client roaming. The customer data center must have two WLCs and the core switches for the network. Which type of wireless architecture must be used? |
| A. cloud | | B. centralized | | C. autonomous | | D. distributed |
B. centralized
Explanation:
For a technology company with multiple buildings requiring seamless wireless coverage, client roaming, and centralized data center with two WLCs (Wireless LAN Controllers) along with core switches, a centralized wireless architecture is most suitable. This architecture allows for easier management of the network from a central location. References := CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice
Question # 6
| During a wireless network design, a customer requires wireless coverage on the perimeter of a building but also wants to minimize signal leakage from the wireless network. Which antenna should be used to accomplish this design? |
| A. Patch | | B. Dipole | | C. Monopole | | D. Omnidirectional |
A. Patch
Explanation:
A Patch antenna should be used to provide wireless coverage on the perimeter of a building while minimizing signal leakage. Patch antennas have a directional radiation pattern that can be focused along the perimeter.
https://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing-combined/industrial-routers-and-industrial-wireless-antenna-guide/ANT-MP-INT-OUT-M.html
Question # 7
| An engineer must perform a Layer 2 survey for a mining facility. Which type of antenna does the engineer use in the mine shaft? |
| A. omnidirectional | | B. patch | | C. internal | | D. dipole |
A. omnidirectional
Explanation:
In a mining facility, especially within mine shafts where the environment can be long and narrow, an omnidirectional antenna is typically used for a Layer 2 survey. This type of antenna radiates RF signal equally in all directions, providing coverage along the length of the shaft.
Question # 8
| A customer celled with a requirement that internal clients must be on different subnets depending on the building they are in, AH access points are operating in local mode and will not be modified, and this is a single controller solution. Which design approach creates the desired result? |
| A. Create an SSID, place it to the desired VLAN under WLANs, and configure 802 lx in ISE to assign the correct VLAN based on the SSID from which the client is authenticating. | | B. Create FlexConnecI groups, place the access points in. and sat the correct VLAN to SSID mapping based on location. | | C. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location. | | D. Create mobility anchors for the SSID, and on the controller under the internal SSID. create a foreign map to the desired VLAN based on location. |
C. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.
Explanation:
AP groups allow the mapping of specific WLANs (SSIDs) to distinct VLANs for different locations. This design enables clients to be on different subnets based on their building location without modifying the access points’ mode of operation.
Question # 9
| An engineer is performing an AP-on-a-stick survey and ¬nds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.) |
| A. Raise the minimum data rate to 24 Mbps. | | B. Increase AP transmit power to improve the SNR. | | C. Allow the use of UNII-2e channels. | | D. Use directional antennas to limit the coverage area of some APs. | | E. Enable power saving mode. |
A. Raise the minimum data rate to 24 Mbps.
D. Use directional antennas to limit the coverage area of some APs.
Explanation:
Raising the minimum data rate to 24 Mbps will reduce the range at which devices can connect, thereby reducing channel overlap. Using directional antennas can also help limit the coverage area of some APs, which can further reduce channel overlap by focusing the signal in specific directions rather than in a broad coverage pattern. References: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)
Question # 10
| A customer has a centralized wireless deployment with N+1 high availability and few open authentication SSIDs configured. After fail over, all APs are broadcasting all SSIDs, but the clients are assigned IP addresses from a different subnet. The WLANs on both WLCs are configured with the same dynamic interfaces. Which feature must be incorporated in the wireless design of the second controller? |
| A. RF Protocol | | B. AP Groups | | C. VLAN Select | | D. AAA Override |
C. VLAN Select
Explanation:
VLAN Select is a feature that allows for the assignment of clients to different VLANs based on various criteria, such as user credentials or device type. In a centralized wireless deployment with N+1 high availability, incorporating VLAN Select can ensure that clients maintain consistent IP addressing across failovers, preventing them from being assigned IP addresses from a different subnet.
Get 196 Designing Cisco Enterprise Wireless Networks (ENWLSD) questions Access in less then $0.12 per day.
Cisco Bundle 1:
1 Month PDF Access For All Cisco Exams with Updates
$100
$400
Buy Bundle 1
Cisco Bundle 2:
3 Months PDF Access For All Cisco Exams with Updates
$200
$800
Buy Bundle 2
Cisco Bundle 3:
6 Months PDF Access For All Cisco Exams with Updates
$300
$1200
Buy Bundle 3
Cisco Bundle 4:
12 Months PDF Access For All Cisco Exams with Updates
$400
$1600
Buy Bundle 4
Disclaimer: Fair Usage Policy - Daily 5 Downloads
Designing Cisco Enterprise Wireless Networks (ENWLSD) Exam Dumps
Exam Code: 300-425
Exam Name: Designing Cisco Enterprise Wireless Networks (ENWLSD)
- 90 Days Free Updates
- Cisco Experts Verified Answers
- Printable PDF File Format
- 300-425 Exam Passing Assurance
Get 100% Real 300-425 Exam Dumps With Verified Answers As Seen in the Real Exam. Designing Cisco Enterprise Wireless Networks (ENWLSD) Exam Questions are Updated Frequently and Reviewed by Industry TOP Experts for Passing CCNP Enterprise Exam Quickly and Hassle Free.
Cisco 300-425 Test Dumps
Struggling with Designing Cisco Enterprise Wireless Networks (ENWLSD) preparation? Get the edge you need! Our carefully created 300-425 test dumps give you the confidence to pass the exam. We offer:
1. Up-to-date CCNP Enterprise practice questions: Stay current with the latest exam content.
2. PDF and test engine formats: Choose the study tools that work best for you.
3. Realistic Cisco 300-425 practice exam: Simulate the real exam experience and boost your readiness.
Pass your CCNP Enterprise exam with ease. Try our study materials today!
Official ENWLSD exam info is available on Cisco website at https://www.cisco.com/site/us/en/learn/training-certifications/exams/enwlsd.html
Prepare your CCNP Enterprise exam with confidence!We provide top-quality 300-425 exam dumps materials that are:
1. Accurate and up-to-date: Reflect the latest Cisco exam changes and ensure you are studying the right content.
2. Comprehensive Cover all exam topics so you do not need to rely on multiple sources.
3. Convenient formats: Choose between PDF files and online Designing Cisco Enterprise Wireless Networks (ENWLSD) practice questions for easy studying on any device.
Do not waste time on unreliable 300-425 practice test. Choose our proven CCNP Enterprise study materials and pass with flying colors. Try Dumps4free Designing Cisco Enterprise Wireless Networks (ENWLSD) 2024 material today!
-
Assurance
Designing Cisco Enterprise Wireless Networks (ENWLSD) practice exam has been updated to reflect the most recent questions from the Cisco 300-425 Exam.
-
Demo
Try before you buy! Get a free demo of our CCNP Enterprise exam dumps and see the quality for yourself. Need help? Chat with our support team.
-
Validity
Our Cisco 300-425 PDF contains expert-verified questions and answers, ensuring you're studying the most accurate and relevant material.
-
Success
Achieve 300-425 success! Our Designing Cisco Enterprise Wireless Networks (ENWLSD) exam questions give you the preparation edge.
If you have any question then contact our customer support at live chat or email us at support@dumps4free.com.
| 
