- Email support@dumps4free.com
Topic 1: Exam Pool A
Which of the following would MOST likely be used to obtain electronic images of a large number of printed documents?
A. NFC device
B. ADF/flatbed scanner
C. Camera/webcam
D. QR scanner
Explanation: ADF/flatbed scanner would most likely be used to obtain electronic images of a large number of printed documents.
References: CompTIA A+ Certification Exam Guide,
Exam 220-1001, Page 351
While implementing a non-carrier-grade wireless backhaul, a technician notices the current channel selection is extremely polluted with various RF signals. Upon performing a spectral analysis, the technician discovers a channel containing almost no RF pollution. Unfortunately, the technician is unable to select that channel. Which of the following is the MOST likely reason for this issue?
A. The channel is reserved for licensed band use.
B. The channel selection is defective; contact the manufacturer.
C. The channel must be unlocked by the vendor.
D. The device requires a firmware update to unlock the channel.
Explanation: The most likely reason that the technician is unable to select the channel with almost no RF pollution is that it is reserved for licensed band use. Some channels are reserved for specific purposes and require a license to use. These licensed bands are typically used for critical infrastructure, public safety, or military operations, and unlicensed devices are not allowed to use them. References: CompTIA A+ Certification Exam Objectives - 220-1001: 3.3 Compare and contrast common networking hardware devices.
A network administrator was notified that laptop users are unable to access or ping any network resources on the corporate network. Which of the following should the network administrator check FIRST?
A. DHCP
B. AAA
C. DNS
D. ARP
Explanation: Domain Name System (DNS) is an Internet service that translates domain names (e.g., its.umich.edu) into IP addresses. Dynamic Host Configuration Protocol (DHCP) is a protocol for automatically assigning IP addresses and other configurations to devices when they connect to a network.
An engineer is experiencing unexpected reboots on a graphics workstation when rendering complex 3-D models. The workstation is configured with a 115V power supply that is rated at 200W and connected to a UPS. The central processing unit contains 16 hyperthreaded cores, and a discrete graphics solution utilizing an 8-pin power connector is installed in a PCI Express x16 slot. Which of the following indicates where the technician should begin troubleshooting?
A. The UPS, as 115V is insufficient for the configuration and should be increased to 220V
B. The power supply, as 200W is insufficient when the GPU is heavily tasked
C. The graphics card, as it is the component that triggers the unexpected reboots
D. The motherboard, as only standard PCI slots should be used for high-end graphics cards, not PCI Express slots
Explanation: The unexpected reboots on a graphics workstation when rendering complex 3-D models may be caused by insufficient power supply. The workstation is configured with a 115V power supply that is rated at 200W, which may not be enough when the GPU is heavily tasked. The technician should begin troubleshooting by checking the power supply.
Laura, a customer, has instructed you to configure her home office wireless access point.
She plans to use the wireless network for finances and has requested that the network be
setup with the highest encryption possible.
Additionally, Laura knows that her neighbors have wireless networks and wants to ensure
that her network is not being interfered with by the other networks.
She requests that the default settings be changed to the following.
Wireless Name: HomeWiFi
Shared Key: CompTIA
Router Password: Secure$1
Finally, Laura wants to ensure that only her laptop and Smartphone can connect to the
network.
Laptop: IP Address 192.168.1.100
Hardware Address: 00:0A:BF:03:C4:54
Smartphone: IP Address 192.168.1.101
Hardware Address: 09:2C:D0:22:3F:11
INSTRUCTIONS
Configure Laura’s wireless network using the network adapter window.
If at any time you would like to bring back the initial state of the situation, please click the
Reset All button.
| Page 3 out of 159 Pages |
| Previous |